PLA DC-Load
PLA DC-Load
The small one up to 1.500 W
Easy to use
PLA series Electronic Loads combine the classic design of large, easy-to-read displays with modern interfaces and a wide range of functions. The devices can be optionally equipped with various data interfaces. In addition to Ethernet, USB, RS-232, a CAN interface can also be built in as an option. GPIB is also available as an option for the devices from 400 W upwards. An I/O port is available as standard.
Diverse
The devices have the operating modes constant current, constant voltage, constant resistance and constant power, where the resistance and power control is realized by software. In addition, a limit value for voltage or current can be set in each operating mode. Dynamic processes can be simulated with up to 100 setting values. An automatic DAQ function allows to store up to 100 measurement data sets (time, voltage, current) internally.
Measurement data acquisition (DAQ)
In digital remote control mode, the electronic load can store synchronous voltage and current with time stamp at a variable interval. You decide whether the recording ends at the end of the data storage or whether the old data is overwritten in the ring buffer principle.
Characteristic curve function
With the characteristic curve function, a sequence of voltage values is linearly interpolated and mapped to a sequence of current values. The characteristic curve to be mapped is defined by setting the voltages and currents sequence each with an SCPI command. Depending on the value of the input voltage, the PLA Load sets the current that corresponds to the interpolated point of the characteristic curve. Up to 100 points are possible.
MPP Tracking
The Maximum Power Point Tracking (MPPT) function consists of the both subfunctions sweeping and tracking, which constantly alternate in an adjustable interval. If the measured Idle Voltage Start is greater than the Minimum Voltage, the electronic load performs a sweep and then readjusts the global MPP found.
- I/O port serially
- Optional: Ethernet/USB/RS-232, CAN, GPIB
- MPP Tracking
- SCPI programming with measuring function
- 19-inch mountable
- Loading inputs front and rear
- Quiet exhauster cooling
- Adjustable limit values for current or voltage
- Dynamic loadings
- Depending on the model up to 1.5 times the power via loadbar
- Electronic protection
| Description | Power | Voltage | Current | Dimensions |
|---|---|---|---|---|
| PLA206 | 200 W | 60 V | 30 A | ½ 19“ x 1 U x 301 mm |
| PLA206C4 | 200 W | 60 V | 4 A | ½ 19“ x 1 U x 301 mm |
| PLA212 | 200 W | 120 V | 15 A | ½ 19“ x 1 U x 296 mm |
| PLA212C2 | 200 W | 120 V | 2 A | ½ 19“ x 1 U x 296 mm |
| PLA230 | 200 W | 300 V | 6 A | ½ 19“ x 1 U x 296 mm |
| PLA280 | 200 W | 800 V | 3 A | ½ 19“ x 2 U x 301 mm |
| PLA406 | 400 W | 60 V | 30 A | ½ 19“ x 2 U x 301 mm |
| PLA406C8 | 400 W | 60 V | 8 A | ½ 19“ x 2 U x 301 mm |
| PLA506 | 500 W | 60 V | 30 A | ½ 19“ x 2 U x 301 mm |
| PLA412 | 400 W | 120 V | 15 A | ½ 19“ x 2 U x 296 mm |
| PLA412C4 | 400 W | 120 V | 4 A | ½ 19“ x 2 U x 296 mm |
| PLA512 | 500 W | 120 V | 15 A | ½ 19“ x 2 U x 296 mm |
| PLA430 | 400 W | 300 V | 6 A | ½ 19“ x 2 U x 296 mm |
| PLA480 | 400 W | 800 V | 3 A | ½ 19“ x 2 U x 301 mm |
| PLA806 | 800 W | 60 V | 80 A | 19“ x 2 U x 306 mm |
| PLA806C16 | 800 W | 60 V | 16 A | 19“ x 2 U x 301 mm |
| PLA1006 | 1.000 W | 60 V | 80 A | 19“ x 2 U x 306 mm |
| PLA812 | 800 W | 120 V | 40 A | 19“ x 2 U x 310 mm |
| PLA812C8 | 800 W | 120 V | 8 A | 19“ x 2 U x 296 mm |
| PLA1012 | 1.000 W | 120 V | 40 A | 19“ x 2 U x 310 mm |
| PLA830 | 800 W | 300 V | 16 A | 19“ x 2 U x 296 mm |
| PLA880 | 800 W | 800 V | 8 A | 19“ x 2 U x 296 mm |
| PLA1206 | 1.200 W | 60 V | 120 A | 19“ x 2 U x 306 mm |
| PLA1206C24 | 1.200 W | 60 V | 24 A | 19“ x 2 U x 296 mm |
| PLA1506 | 1.500 W | 60 V | 120 A | 19“ x 2 U x 306 mm |
| PLA1212 | 1.200 W | 120 V | 60 A | 19“ x 2 U x 310 mm |
| PLA1212C12 | 1.200 W | 120 V | 12 A | 19“ x 2 U x 296 mm |
| PLA1512 | 1.500 W | 120 V | 60 A | 19“ x 2 U x 310 mm |
| PLA1230 | 1.200 W | 300 V | 24 A | 19“ x 2 U x 296 mm |
| PLA1280 | 1.200 W | 800 V | 12 A | 19“ x 2 U x 296 mm |
PLA DC-Load
The small one up to 1.500 W
Easy to use
PLA series Electronic Loads combine the classic design of large, easy-to-read displays with modern interfaces and a wide range of functions. The devices can be optionally equipped with various data interfaces. In addition to Ethernet, USB, RS-232, a CAN interface can also be built in as an option. GPIB is also available as an option for the devices from 400 W upwards. An I/O port is available as standard.
Diverse
The devices have the operating modes constant current, constant voltage, constant resistance and constant power, where the resistance and power control is realized by software. In addition, a limit value for voltage or current can be set in each operating mode. Dynamic processes can be simulated with up to 100 setting values. An automatic DAQ function allows to store up to 100 measurement data sets (time, voltage, current) internally.
Measurement data acquisition (DAQ)
In digital remote control mode, the electronic load can store synchronous voltage and current with time stamp at a variable interval. You decide whether the recording ends at the end of the data storage or whether the old data is overwritten in the ring buffer principle.
Characteristic curve function
With the characteristic curve function, a sequence of voltage values is linearly interpolated and mapped to a sequence of current values. The characteristic curve to be mapped is defined by setting the voltages and currents sequence each with an SCPI command. Depending on the value of the input voltage, the PLA Load sets the current that corresponds to the interpolated point of the characteristic curve. Up to 100 points are possible.
MPP Tracking
The Maximum Power Point Tracking (MPPT) function consists of the both subfunctions sweeping and tracking, which constantly alternate in an adjustable interval. If the measured Idle Voltage Start is greater than the Minimum Voltage, the electronic load performs a sweep and then readjusts the global MPP found.
- I/O port serially
- Optional: Ethernet/USB/RS-232, CAN, GPIB
- MPP Tracking
- SCPI programming with measuring function
- 19-inch mountable
- Loading inputs front and rear
- Quiet exhauster cooling
- Adjustable limit values for current or voltage
- Dynamic loadings
- Depending on the model up to 1.5 times the power via loadbar
- Electronic protection
| Description | Power | Voltage | Current | Dimensions |
|---|---|---|---|---|
| PLA206 | 200 W | 60 V | 30 A | ½ 19“ x 1 U x 301 mm |
| PLA206C4 | 200 W | 60 V | 4 A | ½ 19“ x 1 U x 301 mm |
| PLA212 | 200 W | 120 V | 15 A | ½ 19“ x 1 U x 296 mm |
| PLA212C2 | 200 W | 120 V | 2 A | ½ 19“ x 1 U x 296 mm |
| PLA230 | 200 W | 300 V | 6 A | ½ 19“ x 1 U x 296 mm |
| PLA280 | 200 W | 800 V | 3 A | ½ 19“ x 2 U x 301 mm |
| PLA406 | 400 W | 60 V | 30 A | ½ 19“ x 2 U x 301 mm |
| PLA406C8 | 400 W | 60 V | 8 A | ½ 19“ x 2 U x 301 mm |
| PLA506 | 500 W | 60 V | 30 A | ½ 19“ x 2 U x 301 mm |
| PLA412 | 400 W | 120 V | 15 A | ½ 19“ x 2 U x 296 mm |
| PLA412C4 | 400 W | 120 V | 4 A | ½ 19“ x 2 U x 296 mm |
| PLA512 | 500 W | 120 V | 15 A | ½ 19“ x 2 U x 296 mm |
| PLA430 | 400 W | 300 V | 6 A | ½ 19“ x 2 U x 296 mm |
| PLA480 | 400 W | 800 V | 3 A | ½ 19“ x 2 U x 301 mm |
| PLA806 | 800 W | 60 V | 80 A | 19“ x 2 U x 306 mm |
| PLA806C16 | 800 W | 60 V | 16 A | 19“ x 2 U x 301 mm |
| PLA1006 | 1.000 W | 60 V | 80 A | 19“ x 2 U x 306 mm |
| PLA812 | 800 W | 120 V | 40 A | 19“ x 2 U x 310 mm |
| PLA812C8 | 800 W | 120 V | 8 A | 19“ x 2 U x 296 mm |
| PLA1012 | 1.000 W | 120 V | 40 A | 19“ x 2 U x 310 mm |
| PLA830 | 800 W | 300 V | 16 A | 19“ x 2 U x 296 mm |
| PLA880 | 800 W | 800 V | 8 A | 19“ x 2 U x 296 mm |
| PLA1206 | 1.200 W | 60 V | 120 A | 19“ x 2 U x 306 mm |
| PLA1206C24 | 1.200 W | 60 V | 24 A | 19“ x 2 U x 296 mm |
| PLA1506 | 1.500 W | 60 V | 120 A | 19“ x 2 U x 306 mm |
| PLA1212 | 1.200 W | 120 V | 60 A | 19“ x 2 U x 310 mm |
| PLA1212C12 | 1.200 W | 120 V | 12 A | 19“ x 2 U x 296 mm |
| PLA1512 | 1.500 W | 120 V | 60 A | 19“ x 2 U x 310 mm |
| PLA1230 | 1.200 W | 300 V | 24 A | 19“ x 2 U x 296 mm |
| PLA1280 | 1.200 W | 800 V | 12 A | 19“ x 2 U x 296 mm |